OMRON CP1E-NA20DR-A Manual CP1E-NA20DR-A OPERATION MANUAL

Model: C200HW-ME04K.
Capacity: 4K words.Description : Connects peripheral port to D-sub 9pin connector.
Must be used with CS1W-CN114 (3.3m).Model: C500-CN312N.
Cable length 30cm.
CV Series C Series Expansion ← → I / O device CPU Connecting cable(Vertical-wired)Product name: E@@S type CPU Units with 14 I/O Points CP1E-NA20DR-A OPERATION MANUAL.
Specifications: Power Supply, 100 to 240 VAC; Inputs, 8;Outputs, 6;
Output type, Relay; Program capacity, 2K steps; memory Data capacity, 2K words CP1E-NA20DR-A
External powersupply(24 VDC): --.
Current consumption: 5 V, 0.16A; 24 V，0.07A.
Standards: CE.
The CP1E Programmable Controller: Economical, Easy to use, and Efficient.
The E@@(S)-type Basic CPU Units provide cost,
performance and easy application with only basic functionality CP1E-NA20DR-A OPERATION MANUAL.
The N@@(S@) and NA-types Application CPU Units,
support Programmable Terminal connection, position control,
and inverter connection. Protector for Simple Expansion I/O Rack connector CV500-COV04Unit classification: CJ1 CPU Bus Units.
Product name: Motion Control Unit with,
MECHA TROLINK-II interface.
Specifications: Control modes : Position,
speed, or torque control via MECHATROLINK-II,
Control axes : 32 axes max CP1E-NA20DR-A OPERATION MANUAL. (30 physical axes,
2 virtua axes).
Internal programming language: Special motion contro
language
No. of unit numbers allocated: 1.
Current consumption: 5V, 0.60A; 24V, --.
Standards: UC1, CE.
Improve Equipment Design Efficiency,
and Shorten Tact Time.
Control Servos for up to 16 axes in,
a motion network with one Position,
Control Unit that supports MECHATROLINK-II.
MECHATROLINK-II is a registered trademark,
of the MECHATROLINK Members Association. Output method: Analog resolution: 1/6000.
Analog Inputs: 2.
Analog Outputs: 1.Unit type: CS1 Special I/O Units.
Product name: Isolated-type,
Thermocouple Input Units.
points Input: 4 inputs.
Signal range selection:
Set separately for each input.
I/O type: R, S, K, J, T, L, B.
Conversion speed: 250 ms/4 inputs.
Externa connection: Removable erminal block.
No. of unit numbers allocated: 1.
Current consumption: 5V, 0.25A; 26V, --.
Standards: UC1, CE.
Provides the functionality of isolators,
power supplies, signal converters,
and other devices.
The Analog Input Unit converts analog,
input signals such as 1 to 5 V or 4 to 20mA,
into digital values, and takes the values,
scaled in industrial units, and transfers,
it to the CPU Unit as the process value.
Because of this, no ladder program is required,
at the CPU Unit for scaling.
The Analog Output Unit converts analog output set,
values from the CPU Unit to analog output signals,
such as 4 to 20 mA or 1 to 5 V, and outputs them.
The built-in functions, such as measurement value,
alarms, rate-of-change calculations, and square roots,
have enabled major savings in cost and space compared,
with previous systems CP1E-NA20DR-A Manual.
High-resolution Models and 8-point Input Models are,
also available.
By combining the Units, logging/monitoring.
systems can be constructed,
or the Units can be used together with LCBs/LCCUs,
to construct complete process control systems CP1E-NA20DR-A Manual.
Parameters can be easily displayed and set in an,
easy-to-understand form without special tools.